USART communication on STM32L476G Discovery

I have two boards: a NUCLEO-F411RE and a STM32L467G Discovery.

I need to make a Virtual Com connection between my STM32L467G Discovery and my PC.

For the NUCLEO : The USART2 is connected to ST-Link, so i can communicate with my PC with USART on USB. So, I enable the GPIOA and USART2 Clock. After that, i configure my GPIOA to link Ports 2 and 3 on the USART2, and it works well! I can receive some characters on my PC.

For the STM32L467G Discovery : The STM32L467G Discovery has the USART2 on Port 2 and 3 on GPIOA too. But, in the documentation, they say that the USART2 is connected with the ST-Link with USART2 on Port 5 and 6 in GPIOD. So, i have modify my souce code but i can't receive anything in my computer..

Check my sources:

Main.c

#include "stm32l4xx.h"
#include "stm32l476g_discovery.h"


UART_HandleTypeDef huart2;
GPIO_InitTypeDef GPIO_InitStruct;
void configure_system_clock(void);

int main(void)
{

    HAL_Init(); // HAL Init

    configure_system_clock(); // Configure Clock


    __GPIOD_CLK_ENABLE(); // Enable GPIOD clock
    __USART2_CLK_ENABLE(); // Enable USART2 Clock


    huart2.Instance = USART2;
    huart2.Init.BaudRate = 9600;
    huart2.Init.WordLength = UART_WORDLENGTH_8B;
    huart2.Init.StopBits = UART_STOPBITS_1;
    huart2.Init.Parity = UART_PARITY_NONE;
    huart2.Init.Mode = UART_MODE_TX_RX;
    huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE;
    HAL_UART_Init(&huart2);



            /**USART2 GPIO Configuration
            PA2     ------> USART2_TX
            PA3     ------> USART2_RX
            */
    GPIO_InitStruct.Pin = GPIO_PIN_5|GPIO_PIN_6;
    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
    GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

    char *msg = "Hello YOU\n\r";

          HAL_UART_Transmit(&huart2, (uint8_t*)msg, 15, 0xFFFF);
      while (42);
}

void configure_system_clock(void)
{
    RCC_OscInitTypeDef RCC_OscInitStruct;
    RCC_ClkInitTypeDef RCC_ClkInitStruct;

    __PWR_CLK_ENABLE();

    __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);

    RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
    RCC_OscInitStruct.HSIState = RCC_HSI_ON;
    RCC_OscInitStruct.HSICalibrationValue = 6;
    RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
    RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
    RCC_OscInitStruct.PLL.PLLM = 8;
    RCC_OscInitStruct.PLL.PLLN = 336;
    RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV7;
    RCC_OscInitStruct.PLL.PLLQ = 7;
    HAL_RCC_OscConfig(&RCC_OscInitStruct);

    RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1;
    RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
    RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
    RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
    RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
    HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);
}

This code works fine on the Nucleo NUCLEO-F411RE (but with GPIOA and port 2 and 3).

On my STM32L467G Discovery, that code totaly fail, with GPIOD port 5 and 6 && with GPIOA port 2 and 3.

I can't see the problem, can you help me please?

Solution

You are initializing the UART in the main and that could be ok, but you are not catching the way HAL libraries want you to initialize the peripheral's pin. You should do that in the HAL_UART_MspInit() function you can find in stm32f4_hal_msp.c file.

Your main should look like this

HAL_Init(); // HAL Init

configure_system_clock(); // Configure Clock

huart2.Instance = USART2;
huart2.Init.BaudRate = 9600;
huart2.Init.WordLength = UART_WORDLENGTH_8B;
huart2.Init.StopBits = UART_STOPBITS_1;
huart2.Init.Parity = UART_PARITY_NONE;
huart2.Init.Mode = UART_MODE_TX_RX;
huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE;
HAL_UART_Init(&huart2); 

 HAL_UART_Transmit(&huart2, (uint8_t*)msg, 15, 0xFFFF);

Then in your HAL_UART_MspInit(UART_HandleTypeDef* huart) you should have something like this:

GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART2)
{
 /* Peripheral clock enable */
 __USART2_CLK_ENABLE();
 __GPIOD_CLK_ENABLE();

/**USART2 GPIO Configuration  */
GPIO_InitStruct.Pin = GPIO_PIN_5|GPIO_PIN_6;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);

    HAL_NVIC_SetPriority(USART2_IRQn, 0, 1);
    HAL_NVIC_EnableIRQ(USART2_IRQn);
}

Pay attention to "GPIO_PULLUP", I suggest you to config GPIO like this for UART. You also have to define the UART Handler in your stm32f4_it.c file:

void USART2_IRQHandler(void)
{
 HAL_UART_IRQHandler(&huart2);
}